Minggu, 30 Oktober 2016


I got my copy of Qaqamiig?ux? in the mail the other day.  I was expecting a smaller book for some reason.  As it turned out, the book is hard bound and a full 8-1/2 x 11 inches in size and has 382 pages. 
The content is just what the title advertises, a description of traditional foods and how to prepare them.  Nutrition information on various foods is also provided along with safety tips. 
Contents are grouped by food type, marine mammals, fish, birds, caribou/reindeer, plants, tidal foods and other.
If you are not an Alaskan Native or a guest of Alaskan Natives, marine mammals will not be accessible to you, but all the other foods are available to the general public. 
If you were raised outside of Alaska, much of this food will look alien to you, but if you live in Alaska most of it will look familiar.
The book contains a good deal of historical information on how animals were hunted and caught, something that might be of interest to kayak builders given that one of the primary uses of kayaks was as a vessel to hunt and fish out of.
The book contains lots of photos both color and black and white of how the food is gathered and prepared and gives you a good sense of contemporary food culture in the Aleutians.
My only complaint about the book is that it is missing the customary picture of the author.
Read More..

Jumat, 28 Oktober 2016

G9 minus three

Three days to go. With G9 getting closer, Im trying to get the boat and trailer ready to travel. Today I bought some Boat Buckle straps for the transom, and attached them to the trailer. Aside from having to buy 3/8" bolts, because the supplied 1/2" bolts were too large for the holes in my trailer, THAT part went pretty easily.

Boat Buckle tie-down straps for the transom
Im running into trouble at the other end of the trailer, however. I installed a "Y" shaped piece to support the bow. Unfortunately, the support arm does not reach far enough for it to make contact with the boat, even with the winch post shifted as far back as possible. Not only that, but the bow eye is right in the way.



Time for some troubleshooting, but it will have to wait for tomorrow.
Read More..

Kamis, 27 Oktober 2016

Construction progresses.  After I set up the deck, I started adding deck beams.  They are temporarily nailed in place 3/4 inches below the top of the gunwales. 

Before starting to add deck beams, it is a good idea to stabilize the deck by lashing the ends together and also doweling the two sides together so they dont shift with respect with each other which would cause asymmetry in the deck.
The deck prior to pegging the ends and dropping in deck beams.
And here, at the end of the day, all the flat deck beams are trial nailed in place.  You could of course dowel all the deck beams in place as you go but trial nailing them lets you do some last minute adjustments in deck shape before committing to more permanent joinery.
The last two deck beams to be added are the two curved ones just fore of the cockpit.  Shaping them is more time consuming than shaping the flat ones.  Unlike the flat deck beams which are mounted 3/4 inches below the top of the gunwales, the curved beams are mounted flush with the tops of the gunwales.  A batten is temporary clamped in place to show the curve that the deck stringer will take.  The beam just in front of the cockpit will elevate the front of the coaming 4 inches above the deck.
And here is a view down the length of the boat with all the deck beams in place.  The number of beams, coincidentally is less than in a traditional boat to keep down the overall weight of the finished boat.
And just before I started adding in the two curved deck beams, I had a crisis of faith about where the widest part of the boat should be.  Seemed like it wasnt far back enough.  But then I checked back with the drawing in Arimas book on EA kayaks and it appears that my placement was OK.  Seems that the original for this adaptation was a demo boat done for a Canadian museum and was shorter than the type usually is because available lumber was only 16 feet long.  So a shorter version with a slightly more forward beam was built.  In any case, the first boat of a type is never just right and gets modified when the second one is built.
Read More..

Rabu, 26 Oktober 2016

The Utility Preparing for Planking



A fellow boatbuilder pointed out to me that if I cover the transom first, before planking the sides and bottom of the boat, then the end grain of my planking is going to show around the rim of the transom. (Thanks Chris!) Of course, this only poses an issue if you plan on bright-finishing your transom, which is exactly what I’m planning to do. I’m planning to paint the rest of the hull. So, paint will cover the end grain of the transom as viewed from the side.

So now, my plan has changed to planking the sides and bottom of the boat first. The first pieces of planking that go on will be short 4’ aft sections on the sides. I will be butt-joining these pieces to longer 8’ pieces that will plank the forward sections on the sides. This will allow the butt joint to be located in the flatter aft section of the boat, which means it will be easier to do, and there will be less stress on the joint. I have to join the planking in sections like this, because plywood comes in standard 8’ lengths, and my boat is 11’ long.

In preparation for planking these aft sections, I’ve been sanding away dried runs of epoxy, etc from those parts of the boat I can’t easily get to once the planking is on. I’ve also worked to clean up the shape of the seat riser cutouts in frame #1. Still, before I can plank this aft section, I need to encapsulate these frame cutouts, as well as a couple of other places I won’t be able to reach once the planking is on.

Then, God willing, I should be able to begin planking the little boat.


Dried runs of epoxy have been sanded off of frame #1 and gussets. This is the starboard side.

Starboard frame #1 after sanding. The seat riser cutouts still need to be encapsulated with epoxy.

Port frame #1 after sanding.

Port frame #1 after sanding.

Port frame #1 after sanding.

The globs of epoxy are now sanded off of the transom.

Read More..

Senin, 24 Oktober 2016

Bent Shaft Paddles

Ive been making a number of prototype paddles at the request of a friend and promoter of my paddles.  After a number of weeks I came up with two winners.  One is a bent shaft Greenland style paddle.  The other is an Aleut style paddle with some amount of extra bend added to it.
There were some other paddles in the mix that werent winners but they were instrumental in helping me figure out the specifics of what made the winning models work. I have made Greenland style bent shaft paddles before and quite by luck come up with the right design, but this time, I did some deviation from the winning model only to find that the original was still the best. The Greenland style bent shaft may actually have originated in East Greenland as reported by John Brand who found some examples of these paddles in museums and originally thought that they were just straight paddles that had warped over time, but after some reflection decided that they were actually made that way on purpose.
The bent shaft Aleut paddle is not completely new.  I had made two of these before for a friend but never actually paddled them myself.  This time around I did use the bent shaft Aleut paddle and found it to be a useful variation on the standard version that I usually make.
Four paddles out for a test run. From left to right, a Greenland breakdown for a customer, an Aleut with some bend in the direction of the ridged face, a Greenland style with significant bend and another Greenland style with moderate bend.
One of the key aspects of a Greenland paddle is that it is highly symmetrical, that is, no matter how you hold it, its performance is the same.  The Aleut paddle by contrast has a lower degree of symmetry. You can switch right and left blades without changing performance but you cannot change ridged face for flat face without changing performance.  The reason is that in one configuration, the face of the paddle trails the axis of the loom while in the other, it leads the axis of the loom.  Although the amount of offset is small, it nevertheless makes a difference in the way you need to move the paddle through the water to get it to work.
The same is true of the bent shaft Greenland paddle.  The slight amount of offset of the blade has it either leading or trailing the axis of the loom depending on how you hold it.
My insight while doing the testing on the bent shaft paddles was that when you pull a paddle through the water, you move it through an arc during which the angle the blade makes with the water changes.  The efficiency of the paddle is at its greatest when the blade is perpendicular to the surface of the water. As the stroke progresses, the angle the blade makes with the water changes from the vertical and the amount of force you exert that translates into forward motion decreases.  At the same time, the boat is accelerating forward and the water is accelerating backward so that as the stroke progresses it becomes less efficient.  So having the shaft bent to make the blade more vertical at entry into the water improves its efficiency.
On the other hand, when the paddle is used in a low angle cruising position, that is, with the loom held low and close to the deck then the paddle held so that the blade trails the loom makes the blade self orienting and requires less of a tight grip to keep it properly oriented.  While this stroke generates less thrust than the high angle stroke, it is more efficient at lower cruising speed and less tiring in headwind conditions or against the current conditions.
Whether my understanding of the mechanics of these paddles is correct or not, the fact is that they work in practice as confirmed by speed trials with a GPS.
Read More..

Sabtu, 22 Oktober 2016

G9 minus two


Two days to the G9 Boatbuilders Gathering. Ive basically been focusing on getting the boat trailerable. The boat wont be finished, of course, but several other builders have encouraged me to bring it, as-is. 

Hard to resist. Ive wanted to have my own boat at one of these events for years now.

In yesterdays post, I left off at the "predicament" that the bow support would not reach the boat. This morning, I had a mind-blowing epiphany: "Push the boat forward." Sheesh.

True, this does push the boat forward enough that the hull is not being supported by the full length of the bunks, but I think it will be okay. The bow eye placement turned out to be a non-issue... in fact Id say its near ideal.

The locking mechanism on the trailer winch isnt working properly, so for the time being Im using a tie-down strap on the bow.




A state DNR ranger came out today to inspect the hull. This is part of the boat registration process, in order to create a HIN (Hull Identification Number) for the boat.

Piece by piece, step by step... its all slowly coming together.
Read More..

Jumat, 21 Oktober 2016

Shimmin O The Chines

It sounds like it could be the title of an Irish folk ballad... "Shimmin O The Chines." As many ballads go, the actual work has so far been a mixture of hope and tragedy.

Well, perhaps "tragedy" might be a bit of an overstatement. But, what was that I said in the last post? "Two steps forward, one step back?"

In any case, Id made the shims by cutting a 14-inch piece of mahogany in half with a hand saw. Then I planed each half down to approximately 3/16" with a planer/jointer. I epoxied these into position along the low point in the port chine.

When I was planing down the overhanging edge, however, I wasnt paying enough attention to the angle at which I was holding my larger hand plane. Before I knew it, Id inadvertently gouged the side planking. Theres not much I can do about that now, other than fill the gouge in with epoxy. I guess its a good thing I wasnt planning on a bright finish for the sides.
 
Mahogany shims for filling in that low spot along the port chine.


The overhanging edge faired away quickly, but youve gotta watch the angle on those larger hand planes.

A close-up of the gouge in the plywood.

Read More..